THE DETAILED INPUT PARAMETERS IN THE SIMULATION EXPERIMENTS

Large quantities of oil usually remain in oil reservoirs after conventional water floods. A significant part of this remaining oil can still be economically recovered by Water AlternatingGas (WAG) injection. WAG injection involves drainage and imbibition processes taking place sequentially, hence th[r]

paper focused on analysis of shrinkage porosity base on parameters input form Table 4, eachexperiment was repeated five times in order to reduce experimental errors.Table 4. Shrinkage porosity results of the L 27 array design2.3.1. Analysis of casting defectsThe analysis[r]

This paper presents the use of a variable structure radial basis function (RBF) network for identification in PID control scheme. The parameters of PID control are online tuned by a sequential learning RBF network, whose hidden units and connecting parameters are
adapted online. The RBFnetworkbased[r]

in Fig. 5. Comparing the results obtained from biosensorsmade of silicon cantilevers,5which reported a lowest concen-tration of the target ss-DNA of 0.08␮M, our biosensor isable to detect lower concentrations ͑0.01␮M͒. We believe itis possible to further improve the sensi[r]

The remarkable feature of sliding mode control (SMC) is the stability robustness against disturbances and variations of the system. However to design SMC, the exact model of the plant has to be known. Moreover the large gain of an SMC may intensify the chattering on the sliding surface. To cope with[r]

1.2 PROBLEM STATEMENTF.Land is required to make and present a proposal for opportunity venture. Earlymeeting is agreed F.Land would build a 15,000-m2 office building on F.Soft’s own land inSHTP and rent to F.Soft for a certain period of years. After the concession period, theoffice building w[r]

State Key Laboratory of Automotive Safety and Energy, Tsinghua University, Beijing 100084, ChinaBeijing Automotive Technology Center Co. Ltd., Beijing 100020, China2)3)(Received 12 January 2010; Revised 20 July 2010)ABSTRACT−Variable Nozzle Turbocharger (VNT) was invented to solve the problem[r]

17M o l dS t a n d a r d sInjection molds are always made in accordance with the same rules. Therefore, it shouldnot come as a surprise that their design approach is always similar. This holdsparticularly true for the basic components. A great number of companies are specialized[r]

Several industrial experiments are set up using secondorder splitplot
designs (SPDs). These experiments have two types of factors:
wholeplot (WP) factors and subplot (SP) factors. WP factors, also
called hardtochange factors are factors whose levels are hard or expensive
to change. SP factors, also[r]

The purpose of this thesis is to analyse the behaviour of single piles under axial loading, as far as
settlement and load transfer mechanisms are concerned.
It includes a literary review of two elastic theorybased methods, the Poulos and Davis method and the
Randolph and Wroth method, as well[r]

Abstract
The use of anthocyanin as a source of naturaldyes has been increased due to itslack of toxicity. In this study, natural dyes from the mulberry fruits extracted under different operating conditions such as extraction time (2060 min), temperature (4080 0C) and mass of the mulberry (1025 g)[r]

Due to the battery resource constraint, it is a critical issue to save energy in wireless sensor networks, particularly in large sensor networks. One possible solution is to deploy multiple sink nodes simultaneously. In this paper, we propose a protocol called MRMS (Multipath Routing in large scale[r]

... Calibration and Simulation Results 78 5.1 Quasi- static Tests at Room Temperature 78 5.2 Quasi- static Tests at High Temperature 83 5.3 Experiments for Deformation at High Strain. . .DESCRIBING LARGE DEFORMATION OF POLYMERS AT QUASI- STATIC AND HIGH STRAIN RATES HABIB POURIAYEVALI (M.SC., AMIRKA[r]

19. Machining Set-upArtCAMOperating the Proma.• Turn on the Proma machine by pressing the green button on the frontpanel..• Start the Kay control software by double-clicking the desktop icon• At the File | Open box, either, browse and select the