The Layer 2 domain requires a spanning tree protocol. Note that there are no Layer 2 loops in this design, and that spanning tree must be enabled and configured to protect the network from any accidental loops. The recommended spanning tree protocol is Rapid PVST+ for all Layer 2 deployments in a[r]
• Each host connection should be 10/100 Mbps minimum. Step 1 Research equipment pricing Start by going to www.cisco.com and selecting “Products & Services” and following the links to “Switches” to gather basic information. Look specifically at the Catalyst 29xx and 35x[r]
Note: Go to the erase and reload instructions at the end of this lab. Perform those steps on all switches in this lab assignment before continuing. Step 1 Configure the switch Configure the hostname, access, and command mode passwords, as well as the management LAN settings. The[r]
ISDN Parameters 1. In this lab, you will configure ISDN BRI on router1 and router2 using dialer profiles. With dialer profiles, you are effectively moving some of the logical ISDN parameters from the physical BRI/PRI interface to a dialer interface. Any IP packet should represent ‘int[r]
Step 1 Research equipment pricing Start by going to www.cisco.com and selecting “Products & Services” and following the links to “Switches” to gather basic information. Look specifically at the Catalyst 29xx and 35xx models. Use at least three other sources for technolog[r]
Truy cập Cisco.com Bảo hành chỉ cho phép khách truy cập vào Cisco.com. Chính sách Phần mềm Những khách hàng có tập hợp tính năng phần mềm Cisco Catalyst LAN Lite sẽ được cung cấp các bản cập nhật bảo trì và các bản sửa lỗi được thiết kế để duy trì tính tuân t[r]
RSVP Resource Reservation Protocol is the host-to-host communication/negotia- tion of the QoS requirements. Network devices, such as Cisco switches and routers, will listen to the RSVP signaling between two hosts and determine whether the user requesting service, quantity of resource[r]
In campus, LAN technology is a relatively small geographical areas covered by high-speed data network, which includes workstations, personal computers, printers and other devices. It provides the equipments and applications, including shared access, users to exchange[r]
Configure the IP address of your workstation to 10.1.1.10/24 2. Attempt to telnet into the Catalyst switch. You will not be able to get in because you do not know the passwords. The Catalyst 4000 series of switches deals with password recovery much differen[r]
2. Attempt to telnet into the Catalyst switch. You will not be able to get in because you do not know the passwords. The Catalyst 2900 series of switches deals with password recovery in a similar fashion to other IOS devices. The idea is to move the current[r]
[CONFIRM]Y CLEAR THE DLSWITCH CONFIGURATION USING THE FOLLOWING COMMANDS: CONSOLE> ENABLE CLEAR CONFIG ALL This command will clear all configuration in NVRAM.. This command will cause if[r]
dynamic vlan 10 Xóa toàn bộ địa chỉ MAC được học tự động trên VLAN 10. * Chú ý: Bắt đầu từ phiên bản Cisco IOS 12.1(11) EA1, thì câu lệnh clear mac address-table sẽ được thay thế bằng câu lệnh clear mac-address-table. 15.Cấu hình Sticky MAC address
Networks come in all sizes. They can range from simple networks consisting of two computers, to networks connecting millions of devices. The Internet is the largest network in existence. In fact, the term Internet means a ‘network of networks. The Internet provides the services that enable[r]
C ẤU H ÌNH PH ẦN CỨNG CẦN THIẾT ĐỂ CÓ CHỨC NĂNG MULTILAYER SWITCH Tài liệu này phân tích riêng về các sản phẩm switch Catalyst của Cisco. Các switch của các hãng khác khi muốn có thêm chức năng multilayer switching cũng có thể thêm vào các phần cứng có chức năng tương tự như[r]
to V.35 Male Connection to router serial interface (S0 or S1) Step 2 – Connect the Routers and TSUs Start with all equipment turned off. Attach each router to a corresponding TSU V.35 Nx56/64 port using the V.35 DTE cables. Connect the two TSUs together using a special T1 crossover cabl[r]
- Giá trị VTP revision number sẽ tăng lên 1 khi vlan được tạo hoặc thay đổi. 1b. Sử dụng chế độ VLAN database - Chế độ cấu hình VLAN databse thông thường không được tán thành để sử dụng và sẽ không còn khả năng sử dụng nữa đối với một số phiên bản Cisco IOS. Khi bạn tạo V[r]