195 mmÕs…Fig. 11 Calculated displacementwat the free edge after eachlaser pulse as a function of laser energyFig. 12 Comparison between the measured bending anglesand the simulation results obtained using the new methodJournal of Applied Mechanics MAY 2002, Vol. 69 Õ 259͓4͔ Chen, G., Xu, X.,[r]
.. .NUMERICAL SIMULATION OF GEL MATERIALS DESCRIBING NATURAL PATTERN FORMATION Zhang Yang B.Eng (Harbin Institute of Technology, China) A THESIS SUBMITTED FOR THE DEGREE OF MASTER OF ENGINEERING... processes of three types of leaves with different vein structures are also investigated by using the d[r]
The researches revealed that the scroll design can improve the temperature distribution in the reactor and the porous tube for directing hydrogen can increase the penetration depth of hy[r]
A feedback control system usually implements active and semiactive control of seismically excited structures. The objective of the control system is described by a performance index, including weighting matrix norms. The choice of weighting matrices is usually based on engineering experience. A new[r]
Large quantities of oil usually remain in oil reservoirs after conventional water floods. A significant part of this remaining oil can still be economically recovered by Water AlternatingGas (WAG) injection. WAG injection involves drainage and imbibition processes taking place sequentially, hence th[r]
Comparison between experimental data and numerical simulation of a turbine overspeed and guide vane closure in simultaneously for a slow Francis turbine [7] There is a big lack in the li[r]
Nguyên tắc mô phỏng Ổn định động và thư viện mô hình mô phỏng trên Phần mềm PSSE bao gồm các nội dung sau:• Basic Dynamic Simulation. • Simulation Model Library. • Numerical Integration Stability.
Part 2 Lectures In basic computational numerical analysis has contents: Numerical solution of ODEs, numerical solution of PDEs (mathematical introduction, overview of discretization methods for PDEs, elliptic equations,...).
Ứng dụng Ổn định quá độ trên Phần mềm PSSE.NỘI DUNG CHÍNH PHẦN 12 (Application of transient Stability): • Introduction to the test system. • Load flow analysis. • Dynamic simulation setup. • Dynamic simulation setup. • Running a dynamic simulation. • Plotting dynamic simulation outputs.
Phần 17 KHÓA ĐÀO TẠO TÍNH TOÁN ỔN ĐỊNH VÀ ỨNG DỤNG TRÊN PHẦN MỀM PSSE CHO KỸ SƯ HỆ THỐNG ĐIỆN (Ứng dụng tính toán Ổn định điện áp trên Phần mềm PSSE)• PV Simulation Setup PV Simulation Setup • PV Analysis• Exporting the Results to MSExcel• Implementing a Specific PV Transfer• QV Simulation Setu[r]
(NOP).• Click [OK] to the pop-up “If the tool sensor is operational, make sure thatthe tool measure is already done”.• Click [Save the new workpiece origin and back to park position].At this point the machine will move, returning the spindle to its parked position, usually at theleft rear of the tab[r]
TRANG 1 Ứng dụng bộ cân bằng dùng Neural Networks triệt nhiễu giao thoa ký tự trong hệ thống GSM PHẦN 4 SIMULATION CHƯƠNG 1 THIẾT KẾ CHƯƠNG TRÌNH CHƯƠNG 2 KẾT QUẢ MÔ PHỎNG CHƯƠNG 3 CHƯƠN[r]
NGUYÊN TẮC MÔ PHỎNG ỔN ĐỊNH ĐỘNG VÀ CÁC THƯ VIỆN MÔ HÌNH MÔ PHỎNG TRÊN PHẦN MỀM PSSE. NỘI DUNG CHÍNH PHẦN 7 (Dynamic Simulation Principles) tiếp Phần 4: 1. Classification of Variables. 2. Dynamic Simulation Sequence. 3. Overview of Simulation Procedure.
Tài liệu hướng dẫn chi tiết về sử dụng Quartus ii. Đây là một tài liệu rất hữu ích, không thể thiếu đối với bất kỳ sinh viên nào muốn học tốt về ngôn ngữ HDL và phần mềm Quartus ii Introduction This tutorial provides an introduction to simulation of logic circuits using the Graphical Waveform Edito[r]