Pix(config)# aaa authentication http console ccsp Pix(config)# aaa authentication enable console ccsp Ngoài ra ta cũng có thể cấu hình một vài option cho việc kiểm tra trở nên dễ dàng : Pix(config)# auth-prompt prompt Please Authentication Pix(config)# auth-prompt accept Authentication successful Bậ[r]
1w6d: ISAKMP: transform 1, ESP_3DES1w6d: ISAKMP: attributes in transform:1w6d: ISAKMP: authenticator is HMAC−SHA1w6d: ISAKMP: encaps is 11w6d: ISAKMP: SA life type in seconds1w6d: ISAKMP: SA life duration (VPI) of 0x0 0x20 0xC4 0x9B1w6d: validate proposal 01w6d: ISAKMP (0:2): atts are acceptable.[r]
thì việc hội tụ sẽ rất nhanh vì chỉ có thông tin về sự thay đổi được phát ra cho mọi router trong vùng. OSPF có hõ trợ VLSM nên nó được xem là một giao thức định tuyến không theo lớp địa chỉ. RIPv1 không có hỗ trợ VLSM, tuy nhiên RIPv2 có hỗ trợ VLSM. Đối với RIP, một mạng đích cách xa hơn 15[r]
ối với công cộng, không có tính độc quyền Nếu so sánh với RIPv1 và v2 thí OSPF là một giao thức định tuyến nội vi IGP tốt hơn vì khả năng mở rộng của nó. RIP chỉ giới hạn trong 15 hop, hội tụ chậm và đôi khi chọn đường có tốc độ chậm vì khi quyết đ
------------------ show version ------------------ (Displays the systems hardware and software configuration) Cisco Internetwork Operating System Software IOS (tm) 2500 Software (C2500-D-L), Version 12.0(5)T, RELEASE SOFTWARE (fc1) Copyright (c) 1986-1999 by cisco[r]
Answer Key.”1. A router initializes by doing which of the following?A. Loading the NVRAM, the setup procedure, and the operating systemB. Loading the bootstrap, the operating system, and a configuration fileC. Loading the bootstrap, the setup procedure, and the operating system2. During the setup proc[r]
self test, the router executes diagnostics from ROM on all hardware modules. These diagnostics verify the basic operation of the CPU, memory, and network interface ports. After verifying the hardware functions, the router proceeds with software initialization.Locating and Loading Cisco IOS[r]
Giới thiệu hệ điều hành IOS Hệ điều hành ISO IOS là từ viết tắt của Internetwork Operating System: là hệ điều hành mạng của Cisco, giúp cho các thiết bị của Cisco (switch, router) sử dụng được các tập hợp chức năng mạng chạy trên nó (routing, packet switching ) để xây dựn[r]
u của tập tin cấu hình. Nếu câu lệnh boot system chỉ sai IOS thì chúng ta xoá lệnh đó đi bằng lệnh “no” của câu lệnh đó. Router#show version Cisco Interface Operating System Software IOS (tm) C2600 Software (C2600-JK803S-M), Version 12.2 (17a), RELEASE SOFTWARE (fc[r]
u của tập tin cấu hình. Nếu câu lệnh boot system chỉ sai IOS thì chúng ta xoá lệnh đó đi bằng lệnh “no” của câu lệnh đó. Router#show version Cisco Interface Operating System Software IOS (tm) C2600 Software (C2600-JK803S-M), Version 12.2 (17a), RELEASE SOFTWARE (fc[r]
u của tập tin cấu hình. Nếu câu lệnh boot system chỉ sai IOS thì chúng ta xoá lệnh đó đi bằng lệnh “no” của câu lệnh đó. Router#show version Cisco Interface Operating System Software IOS (tm) C2600 Software (C2600-JK803S-M), Version 12.2 (17a), RELEASE SOFTWARE (fc[r]
Step 2 Gather the Facts. You monitor the switch during the reload. C2900XL Boot Loader (C2900-HBOOT-M) Version 12.0(5)XU, RELEASE SOFTWARE (fc1) Compiled Mon 03-Apr-00 17:20 by swati starting Base ethernet MAC Address: 00:02:4b:22:65:c0 Xmodem file system is available. Initializing Flash fla[r]
router(config-line)#password newpassword router(config)#line vty 0 4 router(config-line)#login router(config-line)#password newpassword 9. Copying the startup-configuration to running-configuration. Thực hiện lệnh no shutdown trên tất cả các interface được dùng. 10. Chuyển nội dung thanh ghi về giá[r]
ể OSPF hoạt động đúng bạn cần cấu hình băng thông đúng cho cổng của router. Router (config)#interface serial 0/0 Router(config-if)#bandwidth 64 Giá trị băng thông mặc định của cổng Serial Cisco là 1,544Mbps hay 1544kbs Hình 2.3.3.a. Giá trị chi phí OSPF mặc định của Cisco IOS.
router#show startup-config 8. Đặt lại password mới: router#config term router(config)#enable secret newpassword router(config)#enable password newpassword router(config)#line con 0 router(config-line)#login router(config-line)#password newpassword router(config)#line aux 0 router(config-line)#login[r]