thức đúng, cái hợp quy luật hay là đúng với quy luật.- Thực tiễn chẳng những là điểm xuất phát của nhận thức, là yếu tố đóng vai trò quyết định đối với sự hình thành và phát triển của nhận thức mà còn là nơi nhận thức còn phải luôn luôn hớng tới để thể nghiệm tính đúng đắn của SV: Trần Trung Dũng -[r]
TIÊU CHUẨN VIỆT NAM TRANG 4 PHẦN KHÁI QUÁT TÊN GỌI : Tiêu chuẩn hóa trong trình bài tài liệu khoa họcliterature scientific standardized ĐỐI TƯỢNG TIÊU CHUẨN: ISO 7144:1986 Tư liệu – Trìn[r]
Áp dụng mô hình đã đem đến một số ưu điểm và nhược điểm như sau: ƯU ĐIỂM: + Hiệu quả tác nghiệp cao + Có sự chuyên môn hóa sâu sắc hơn, cho phép các thành viên tập trung vào chuyên môn n[r]
producer will determine whether or not the tubing will beboxed, crated, cartoned, packaged in secured lifts, or bundledto ensure safe delivery unless otherwise instructed. Tubingheavier than 16 gage will normally be shipped loose, bundled,or in secured lifts. Special packaging requiring extra operat[r]
CHÚ THÍCH - Có thể sử dụng nhiệt độ khác của tủ ấm, nh−ng việc xác định và hiệu chuẩn phải đ−ợc thực hiện ở cùng một nhiệt độ sai lệch trong khoảng ± 1 k 7.3.2 Đo phổ Sau ít nhất 60 phút[r]
NOTE 9—When agreed upon by the purchaser and the manufacturer and so stated on the order, pipe may be tested: _1 To 1_1⁄2times the specified working pressure, except that the maximum tes[r]
_8.5.2 Austenitic and Ferritic-Austenitic Stainless Steel_ _Grades—One tension test shall be made for each heat._ 8.5.2.1 When heat treated in accordance with 6.1, the test blank or forg[r]
ORDERING INFORMATION 3.1 Orders for material to this specification should include the following, as required, to describe the desired material adequately: 3.1.1 Quantity feet, centimetre[r]
TENSILE REQUIREMENTS 7.1 The tube prior to the finning operation, or unfinned portions of the finned tube, shall conform to the requirements for tensile properties prescribed in the gove[r]
PERMISSIBLE VARIATIONS IN DIMENSIONS OF SQUARE AND RECTANGULAR TUBING _10.1 Outside Dimensions and Wall Thickness—Variations_ in largest outside dimensions across flats and wall thicknes[r]
ORDERING INFORMATION 3.1 Orders for material under this specification should include the following, as required, to describe the desired material adequately: 3.1.1 Quantity feet or numbe[r]
ORDERING INFORMATION 4.1 Orders for material to this specification should include the following, as required, to describe the desired material adequately: 4.1.1 Quantity number of feet, [r]
HYDROSTATIC TEST 10.1 Each length of Type F, E, or S pipe shall be tested at the mill to the hydrostatic pressures prescribed for butt weld or Grade B pipe as specified in Table X2 for p[r]
CHẤT THẢI NGUY HẠI V Μ KHÔNG NGUY HẠI 5.1 TUÂN THỦ LUẬT PHÁP Nhμ cung cấp IKEA phải đảm bảo tuân thủ toμn bộ các luật vμ điều khoản đ−ợc áp dụng liên quan đến việc l−u trữ, vận chuyển, t[r]
Kiến trúc của hệ thống GPS được thông qua vào năm 1973. Năm 1978, vệ tinhđầu tiên trong hệ thống GPS đã được phóng thành công và tín hiệu GPS đã đượcthu thử nghiệm với các máy thu đầu tiên. Mục đích ban đầu của dự án xây dựng hệthống GPS là để phục vụ các mục đích quân sự của Mỹ, nên Bộ Quốc phòng M[r]