TIÊU CHUẨN VIỆT NAM TRANG 4 PHẦN KHÁI QUÁT TÊN GỌI : Tiêu chuẩn hóa trong trình bài tài liệu khoa họcliterature scientific standardized ĐỐI TƯỢNG TIÊU CHUẨN: ISO 7144:1986 Tư liệu – Trìn[r]
Tiểu luận Triết họclời mở đầuTrong công cuộc xây dựng và phát triển nền kinh tế nhiều thành phần, vận hành theo cơ chế thị trờng, có sự quản lý của Nhà nớc, theo định hớng xã hội chủ nghĩa ở nớc ta hiện nay, lý luận nhận thức, vấn đề cải tạo thực tiễn nền kinh tế luôn thu hút sự quan tâm của nhiều đ[r]
CHÚ THÍCH - Có thể sử dụng nhiệt độ khác của tủ ấm, nh−ng việc xác định và hiệu chuẩn phải đ−ợc thực hiện ở cùng một nhiệt độ sai lệch trong khoảng ± 1 k 7.3.2 Đo phổ Sau ít nhất 60 phút[r]
ORDERING INFORMATION 4.1 Orders for material to this specification should include the following, as required, to describe the desired material adequately: 4.1.1 Quantity number of feet, [r]
HYDROSTATIC TEST 10.1 Each length of Type F, E, or S pipe shall be tested at the mill to the hydrostatic pressures prescribed for butt weld or Grade B pipe as specified in Table X2 for p[r]
REFERENCED DOCUMENTS _2.1 ASTM Standards:_ A 370 Test Methods and Definitions for Mechanical Testing of Steel Products2 A 962/A 962M Specification for Common Requirements for Steel Faste[r]
producer will determine whether or not the tubing will beboxed, crated, cartoned, packaged in secured lifts, or bundledto ensure safe delivery unless otherwise instructed. Tubingheavier than 16 gage will normally be shipped loose, bundled,or in secured lifts. Special packaging requiring extra operat[r]
REFERENCED DOCUMENTS _2.1 ASTM Standards:_ A 29/A 29M Specification for Steel Bars, Carbon and Alloy, Hot-Wrought and Cold-Finished, General Require-ments for2 A 234/A 234M Specification[r]
CHẤT THẢI NGUY HẠI V Μ KHÔNG NGUY HẠI 5.1 TUÂN THỦ LUẬT PHÁP Nhμ cung cấp IKEA phải đảm bảo tuân thủ toμn bộ các luật vμ điều khoản đ−ợc áp dụng liên quan đến việc l−u trữ, vận chuyển, t[r]
considera questo documento come segreto aziendale con DIVIETO PER CHIUNQUE di riprodurlo e/o di renderlo comunque noto, in tutto o in parte, a ter-zi, ovvero a ditte concorrenti, senza s[r]
ORDERING INFORMATION 3.1 Orders for material under this specification should include the following, as required, to describe the desired material adequately: 3.1.1 Quantity feet or numbe[r]
PERMISSIBLE VARIATIONS IN DIMENSIONS OF SQUARE AND RECTANGULAR TUBING _10.1 Outside Dimensions and Wall Thickness—Variations_ in largest outside dimensions across flats and wall thicknes[r]
TENSILE REQUIREMENTS 7.1 The tube prior to the finning operation, or unfinned portions of the finned tube, shall conform to the requirements for tensile properties prescribed in the gove[r]